2025 John Deere 540M NSL

Information

2025 John Deere 540M NSL

  • Superior strength and visibility
  • For heavy-duty chores
  • Parking stands are integrated on the loader

Features may include:

Single-point hydraulic connection saves time

The H310 Loader can be ordered with a single-point hydraulic connection that also incorporates the connection point for any electrical needs. To disconnect the hydraulic connection between the loader and the tractor, it is necessary to relieve the hydraulic system oil pressure on the tractor.

Concealed oil lines improve appearance and reduce damage

Over time, increased width in tractor hoods have caused issues with available space for running traditional oil lines of a loader along the boom, making them more susceptible to damage.

To improve this situation, the oil lines have been routed through the boom arm and the torque tube, improving line protection and the appearance of the loader.

Loader removal (parking) made easy

John Deere loaders are easily removed and reinstalled on tractors without tools. The parking system allows removing or attaching the loader to the tractor in minutes without the need for tools.

To remove or park the loader, apply slight down pressure to the loader boom with the bucket dumped at approximately a 30-degree angle. With the tractor in park, lower the parking stands and place the mast pins in the open position.

Removing or parking the loader

Utilizing the boom circuit with the tractor in neutral, rotate the mast forward until the mast has rotated past the pin location on the mounting frame by extending the lift cylinder. Now using the bucket circuit, roll back the bucket until the mast is removed from the pocket and will clear the tires.

With the tractor in park, shut the engine off and relieve the hydraulic pressure as indicated for the tractor (rotating the joystick). Disconnect or open the single-point hydraulic connector (or remove couplers if no single point is installed).

Store the loader half of the single-point connector or hoses, and back away from the loader.

Boom lockout for easy service

A hydraulic shut-off valve is included with the M & R-Series Utility & Ag Loaders to ensure the loader does not lower suddenly. For example, this allows the boom to be locked out when someone is required to be located under the loader boom for service work on the tractor. It should not be used for extended periods of time unless an appropriate support stand is also utilized.

Photos

Highlights

  • Visalia, California
  • 2025
  • John Deere
  • 540M NSL
  • Available
  • Maximum Lift: 3578 mm (141 in.) | At full height - bucket level: 3383 mm (133 in.) | Reach At maximum height: 1011 mm (39.8 in.) / At ground level - bucket level: 2426 mm (95.5 in) | Clearance at full height - bucket dumped: 2538 mm (100 in.)

Specifications

  • 2025
  • John Deere
  • 540M
  • NSL
  • General
  • 18.4R38
  • 14.9R24
  • Loader raise, seconds: 3.4 seconds / Loader lower, seconds: 2.5 seconds / Bucket dump, seconds: 2.1 seconds / Bucket rollback, seconds: 2.1 seconds
  • Boom breakout force Measured at pivot: 2671 kg / Measured at 800 mm ahead of pivot: 2325 kg | Bucket rollback force capacity: At ground-level line 3046 kg / At maximum height: 1636 kg / At 59-in. (1500-mm) lift height: 2986 kg
  • 75.7 L/min (20 gpm)
  • 195 bar (2828 psi)
  • Bucket used: 1850 mm (73 in.) | Dump angle: -74 degree | Rollback angle: 42 degree | Dump angle, ground: -96 degree (angle)
  • Digging: 47 mm (1.9 in.)
  • Maximum Lift: 3578 mm (141 in.) | At full height - bucket level: 3383 mm (133 in.) | Reach At maximum height: 1011 mm (39.8 in.) / At ground level - bucket level: 2426 mm (95.5 in) | Clearance at full height - bucket dumped: 2538 mm (100 in.)
  • 4.8 m (15.8 ft)
  • 2380 mm (94 in.)
  • at full height: Measured at pivot 1373 kg (3027 lb) / Measured at 800 mm ahead of pivot: 1481 kg | at 59 in. (1500 mm): Measured at pivot 2015 kg / Measured at 800 mm ahead of pivot: 1931 kg
  • Base: 1028.2 kg | Bucket: 246 kg (542 lb)